How To Make Memory Wire Rings

In my previous project, I've showed my way making a vogue memory wire choker necklace. So, I'll continue to show you how to make use of these endless loops in jewelry making. Here, this project is all about a memory wire rings design, in which demonstrates the way making a wire rings and a seed bead sunflower by using brick stich technique. Here we go!

Supplies needed for making a memory wire ring:

8mm Agate Bead
4mm Coconut-Brown Seed Beads
3mm Yellow Seed Beads
3mm Green Seed Beads
2mm Coconut-Brown Seed Beads
Memory Wire
0.3mm Tiger Tail Wire
Round Nose Pliers
Side Cutting Pliers
Wire Cutter Pliers
Hot Melt Glue Gun (optional)

Supplies needed for making a memory wire ring

How to make the memory wire ring?

Step 1: Make the flower disk by using brick stich technique

1st, cut a 60cm piece of tiger tail wire and then slide the 6mm agate bead to 6cm from the other end;
2nd, thread the wire through the bead from left to right to make a loop around the outside of the bead. Then, repeat the same process for another loop;

make two loops around the outside of the bead

3rd, string two 2mm brown seed beads, then pass the wire under the loop around agate bead. Pull the wire to make the two seed beads rest as picture shows. Finally, weave the wire back up through the second seed bead. Tighten the wire then;
4th, slide one 2mm seed bead, pass the wire under the loop around agate bead, then back up through the newly added seed bead. Pull the wire tightly;
5th, repeat the 4th procedure until surround the agate bead with 2mm seed beads;
6th, when exiting the wire at the last seed bead, you should continue to pass it down through the first seed bead and then up through the last seed bead. Pull the wire tightly;

make the first brick stitch around the agate bead

7th, add two 4mm brown seed beads and do the brick stich pattern as did with the 2mm beads.

do the second brick stitch pattern

Step 2: Make the petals with yellow seed beads

1st, once exit the wire at the last 4mm brown seed bead, slide eight 3mm yellow seed beads instead;
2nd, pass the wire back through the last but one seed bead;
3rd, string another eight 3mm yellow seed beads;
4th, pass the wire under the exposed wire between two 4mm brown seed beads;

Make the petal with yellow seed beads

5th, tighten the wire and then repeat the procedures 1~4 for the rest petals.

repeat the procedures 1~4 for the rest petals

Step 3: Prepare the memory wire ring base

Cut a 4-coil memory wire, loop one end with round nose pliers. Then, string the 3mm green seed beads to cover the wire coils. Finally, make a simple loop at the other end to secure the beads stay in place.

Prepare the memory wire ring base

Step 4: Assemble the beaded flower with memory wire ring base

1st, take the semi-finished seed bead sunflower, pass the working wire end down through its adjacent 4mm brown seed bead and 2mm brown seed bead;

pass the working wire end down through the 2 adjacent beads

2nd, take the beaded memory wire ring and cross the two wire ends through the two loops twice or more times;
3rd, knot the wires firmly and then trim off the leftovers;

Assemble the beaded flower with memory wire ring base

4th, seal the part between sunflower and ring with thick glue if necessary.

seal with glue if necessary

Done!

finished memory wire ring

So far, you've created a new floral element for your wardrobe! If you've never work with memory wire, you should know that nothing beats the memory wire in making quick yet stunning jewelry accessory. And this beaded flower memory wire ring is sure to be the next craze among girls! Hope you've enjoyed while making this wire ring!